Climate Simulation Test Equipment For Testing Vulcanized Rubber Ozone Aging Test Chamber
Ozone aging test chamber is one of the climate simulation test equipment for testing vulcanized rubber in the static and dynamic tensile deformation state, exposure to air containing a certain concentration of ozone and a certain temperature environment, but no direct sunlight under the harsh Adaptability test conditions for a variety of research institutes and factories and mines laboratory test samples for the aging test.
It was controlled by the PLC touch screen, temperature control accuracy.
Ozone resistance aging test box is mainly suitable for polymer materials and products (rubber) of the resistance to ozone aging performance test. Ozone content in the atmosphere is very low, but it is the main factors of polymer materials aging. Ozone aging test chamber simulating and strengthen the ozone condition in the atmosphere, get approximate to actual use or reproduction of the test results in a short time. The studay of ozone effect regulation to rubber products, quickly identify and evaluate rubber materials resistance to ozone and antiozonant protection efficiency method, and then take effective aging proof measures to improve the service life of rubber products.
Corresponding standards: JIS K 6259, ASTM1149, ASTM1171, ISO1431, DIN53509, GB/T13642, GB/T 7762-2003, GB 2951
Ozone resistance aging test box is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
Ozone resistance aging test box by the occurrence of silent and efficient ozone generator ozone gas, and a certain amount of air processed, the switch in the mixture into the chamber, the continuous line UV detector to detect the concentration of ozone, ozone generator control feedback to the systems to control system settings according to the occurrence of effective control of ozone to the ozone chamber to maintain the appropriate concentration of work by heating humidification systems to meet all the test conditions.
Colourfastness to ozone for textile color fastness test fabric is mainly used for color fastness properties exposed to ozone environment; it is the special equipment for test the fabric colorfastness to ozone resistance feature.
1. Equipped with high efficiency ozone generator. It is also with HMOS sensor. When the ozone concentration of 5ppm, control accuracy of ± 20%. At the same time with a durable counters. When the tank is full load test, the ozone concentration can reach 5ppm in about five minutes;
2. Stainless steel test chamber is equipped with a large UV glass observation window, and can be closed-loop control of the ozone concentration. Rotating the sample holder can hold up to 24 samples. With automatic shut-off feature LED lights to improve the test chamber observing the effect of test;
3. In order to improve the safety performance of the device is equipped with door safety interlock feature, the ozone decomposition catalyst and exhaust design with negative pressure monitoring;
4. The user can conduct on-site calibration of each year, the sensor can also be returned to the factory for calibration. Two calibration standards have NIST traceable calibration equipment also has periodic reminders to alert users to replace ozone decomposition catalyst and an ozone generator.
1. The apparatus consists of an ozone generator, fans, baffles, sample holder and the sample compartment composition, the use of high-voltage transformer ozone generator discharge through the grid, the generator is placed before the low pressure fan, a separator system by ozone is injected into the test warehouse, sample holder mounted on the wire slip ring separated clip can be applied to samples of various sizes.
2. The device is equipped with high-efficiency ozone generator, controller, closed-loop control of ozone concentration and can accommodate 24 rotating sample holder sample by simply setting the parameters and current parameters pre-set can be displayed on the screen, thereby increasing the accuracy of the device can be manipulated and test results.
Ozone chamber ozone _ for textile color fastness test steps:
1, A control sample and a standard sample, and placed in the oven temperature (64-82F) and a relative humidity of 67% ozone test compartment until control standard colors fade and fade to the same standards.
2, The experimental phase of a cycle, the cycle is repeated until the sample reaches a predetermined color, or reaches a predetermined number of cycles.
3, Observe the degree of discoloration, to arrive at the fabric resistance to ozone color fastness.
|400mm × 400mm × 500mm (depth × width × height)
|Ozone concentration range
|25pphm ~ 800pphm (adjustable)
|RT +10 ℃ ~ 60 ℃ (adjustable)
|O3 concentration fluctuation deviation
|± 1 ℃ (no load)
|± 1 ℃ (no load)
|0 ~ 999 hours (adjustable)
|AC220V ± 10% 50Hz
BOTO GROUP is a professional manufacturer of various kinds of testing equipment over 20 years. BOTO products are widely used in paper products, packaging, ink printing, adhesive tapes, bags, footwear, leather products, environment, toys, baby products, hardware, electronic products, plastic products, rubber products and other industries, and applicable to all scientific research units, quality inspection institutions and academic fields.
BOTO deals with customers from more than 150 countries and regions. Meanwhile, we are committed to cooperate with different dealers in different countries and regions in order to offer better service. Our mission is to help every customers establish testing labs to ensure the quality of their products.
Our company will continue to develop, innovate and keep faith. We combine with the international testing standards and the specific demands of customers that may establish a new banner in Chinese testing industry.
The factory has the ability to calibrate, and the customer can also designate a ISO 17025 accredited third-party organization to calibrate and issue a calibration report.
We control quality from the materials, electronic parts, controller,comppressor, solenoid valve, and many parts of the products.
The certificate is valid until June 17, 2024
During the whole business process, we offer Consultative Selling service.
1) Customer inquiry process:
Discussing testing requirements and technical details, suggested suitable products to customer to confirm. Then quote most suitable price according to customer requirements.
2) Specifications customize process:
Drawing related drawings to confirm with customer for customized requirements. Offer reference photos to show the products appearance. Then, confirm the final solution and confirm final price with customer.
3) Production and delivery process:
We will produce the machines according to confirmed PO requirements. Offering photos to show production process.
After finish production, offer photos to customer to confirm again with the machine. Then do own factory calibration or third party calibration(as customer requirements). Check and test all the details and then arrange packing.
Deliver the products in confirmed shipping time and inform customer.
4) Installation and after sale service:
Defines installing those products in the field and providing after-sales support.